MM Industries

Home › Resources › Standards › IS 2721

Indian Standard explained

IS 2721 explained:
chain link fence fabric

What the Indian Standard for chain link fence fabric requires, what changed in the 2025 revision, and how to write it into a purchase order or tender. Written by MM Industries, manufacturing chain link fence at our own plant in Raipur since 1995.

Manufacturer since 1995 · ISO 9001:2015 certified plant

At a glance

Current editionIS 2721:2025 (Third Revision)
Official titleGalvanized Polyvinyl Chloride (PVC), Polyolefin and Other Polymer Coated Steel Chain Link Fence Fabric — Specification
Established10 December 2025
ReplacesIS 2721:2003, in force alongside it until 10 June 2027
BIS committeeMED 10, Wire Ropes and Wire Products
CertificationVoluntary. BIS lists no Quality Control Order for this product at the time of writing

Quick answer

IS 2721 is the Bureau of Indian Standards specification for steel chain link fence fabric. The current edition is IS 2721:2025, the third revision, established on 10 December 2025. IS 2721:2003 stays in force alongside it until 10 June 2027, after BIS extended its withdrawal by one year, but new tenders and purchase orders should cite IS 2721:2025. The standard governs the wire, its coating, mesh size and tolerance, selvage, roll dimensions and the tests the wire must pass before fabric is accepted.

Scope

What IS 2721 covers

IS 2721 defines chain link fence fabric as steel wire that is helically wound and interwoven into a continuous diamond mesh, with no knots or ties anywhere except at the selvage, where the wire ends are knuckled or twisted. That construction is what separates chain link from welded mesh: every wire is free to articulate, so the fabric follows the ground and spreads an impact load across many links.

The standard covers the fabric only. Line posts, straining posts, struts, base plates and fittings sit outside it, so a complete fence specification has to name those separately. In our experience this is the most common gap in tender documents: the fabric is specified to IS 2721 and the framework is left undefined.

Manufacturer note

The 2025 title now names PVC, polyolefin and other polymer coated chain link fabric alongside galvanized fabric. Coated chain link, sold widely as PVC chain link, is therefore within the scope of the current standard, and a coated order should state the coating type and colour in the same way a galvanized order states the zinc coating.

Latest status

What changed, and when

IS 2721 has been revised three times since it was first issued. The dates below decide which edition a contract can cite.

DateEvent
1964First edition of IS 2721 published by BIS
2003Second revision. Selvage types introduced, fabric length and width set to the purchaser’s requirement, zinc coating raised to heavy coating, packing clause amended
March 2024IS 2721:2003 reviewed by the MED 10 committee
10 December 2025IS 2721:2025, the third revision, established
27 October 2026BIS corrigendum moves the withdrawal of IS 2721:2003 from 10 June 2026 to 10 June 2027
10 June 2027IS 2721:2003 withdrawn. IS 2721:2025 becomes the only valid edition

Both editions are in force together until 10 June 2027. BIS first set the withdrawal of the 2003 edition for 10 June 2026, then extended it by one year through a corrigendum dated 27 October 2026. A contract can still cite IS 2721:2003 until then, but supply after June 2027 must meet IS 2721:2025, so update tender templates and approved vendor documents now.

How to read the figures below

Where this page quotes clause values, such as tolerances, test limits and sampling, they are taken from the 2003 edition, which remains in force until 10 June 2027. Confirm each value against the IS 2721:2025 text before writing it into a contract. Our team will check any clause for you at enquiry.

Requirements

Key requirements of the standard

Wire and coating

  • Mesh wire and line wire are galvanized mild steel wire to IS 280, with a tensile strength of 400 to 550 MPa.
  • The zinc coating is the heavy grade of IS 4826 (hot dip) or IS 12753 (electrogalvanized). Line wire must meet the heavy coating requirement in full.
  • Mesh wire tested after weaving may fall up to 10 percent below the specified minimum zinc mass, an allowance for the coating disturbed during weaving.
  • Wire must be circular and free from scale, splits and other defects, and the zinc coating must be smooth, even and bright.

Mesh size and tolerance

Nominal mesh sizeTolerance
25 mm± 3 mm
40, 50, 63 and 75 mm± 4 mm
100, 125 and 150 mm± 5 mm

Mesh size is the minimum clear distance between parallel wires with the fabric in its normal stretched condition. Sizes outside this range are by agreement between purchaser and manufacturer. Source: IS 2721:2003, Table 1.

Selvage types

TypeTop and bottom edgesTypical use
Both ends twistedWire ends twisted together in a close helix at both edgesHigher security, where a sharp top edge is a deterrent
One end knuckled, one end twistedRounded loop at one edge, twisted points at the otherKnuckled edge at ground level, twisted edge at the top
Both ends knuckledAdjacent wire ends interlocked and bent back into a loop at both edgesSchools, sports grounds and public areas
Both ends neither knuckled nor twistedPlain cut ends at both edgesFabric to be cut or joined on site

Dimensions and workmanship

  • Standard widths of 0.90, 1.20, 1.50, 1.80, 2.00, 2.50 and 3.00 m, or as the purchaser requires.
  • Roll lengths of 5, 10, 15, 20 or 25 m, or as the purchaser requires. Measured fully stretched, a roll must not be shorter than its stated length.
  • Two line wires for fabric up to 2 m high, at top and bottom. Three line wires, at top, middle and bottom, for fabric 2.5 m high and above.
  • No welds or splices within a roll. Rust on cut selvage ends is inherent and is not a ground for rejection.

Acceptance

Tests and acceptance

The mechanical tests are carried out on the coil wire before it is woven, which is why a mill test certificate for the wire is part of every serious chain link supply.

TestRequirementMethod
Tensile400 to 550 MPa for mesh and line wireIS 1608
WrappingNo break or split after eight turns around its own diameter, then straightenedIS 1755
TorsionAt least 18 twists over a length of 100 wire diametersIS 1717
Bend (wire of 5 mm and above)Bent through 90 degrees around a former of twice the wire diameter without breaking or splittingIS 2721
Zinc coatingHeavy coating mass and uniformityIS 4826 or IS 12753

Source: IS 2721:2003, clause 9.

Sampling

Rolls in the lotRolls tested (physical and dimensional)Rolls tested (zinc coating)
Up to 2521
26 to 5031
51 to 15052
151 to 3008 (1 defective allowed)2
301 and above13 (1 defective allowed)2

A lot is all rolls with the same mesh size, wire diameter, width and roll length made under similar conditions. No defective is allowed in the zinc coating sample. Source: IS 2721:2003, Annex A.

Marking on every roll

  • Manufacturer’s name or trademark
  • Lot number and roll number
  • Mesh size and the diameters of line wire and mesh wire
  • Length and width of the fabric
  • The BIS Standard Mark, only where the manufacturer holds a BIS licence for the product

For buyers

How to specify IS 2721 in a purchase order

A tight chain link specification leaves nothing to interpretation at the site gate. This is the checklist our team works through with every buyer.

  • Cite the standard with its year: IS 2721:2025.
  • Mesh size in millimetres, for example 50 mm, and accept the standard tolerance.
  • Mesh wire diameter in millimetres. SWG alone is ambiguous across suppliers.
  • Coating: heavy zinc coating, or the polymer type and colour for coated fabric.
  • Selvage type for the top and bottom edges.
  • Fabric height, roll length and the number of line wires.
  • Documents: wire mill test certificate, lot test report and roll marking as per the standard.

From the plant floor

Weight is the quickest check on a delivered roll. Underweight fabric almost always means thinner wire than ordered. Use our chain link weight calculator to set the theoretical weight per roll before you raise the order, then weigh rolls at receipt.

Our practice

How we manufacture chain link fence

MM Industries manufactures GI and PVC coated chain link fence to IS 2721 at our plant on NH 43, Raipur, which has run since 1995. Our standard range is 2.0 to 4.0 mm wire (14 to 8 SWG) in 25 to 100 mm mesh, in roll heights from 3 to 10 ft. Our quality management system is certified to ISO 9001:2015, and the wire mill test certificate is supplied with every lot.

One practical point for buyers: our 25 mm mesh is made in 14 SWG wire only. If your tender calls for 25 mm mesh in a heavier gauge, speak to our team before the document is issued.

Questions

Frequently asked questions

Yes, until 10 June 2027. BIS established IS 2721:2025 on 10 December 2025 and, by a corrigendum dated 27 October 2026, moved the withdrawal of IS 2721:2003 from 10 June 2026 to 10 June 2027. New tenders and purchase orders should still cite IS 2721:2025.

BIS lists no Quality Control Order for chain link fence fabric at the time of writing, so certification is voluntary.

Yes. The 2025 revision names PVC, polyolefin and other polymer coated chain link fabric in its title, alongside galvanized fabric.

The 2003 edition required 400 to 550 MPa for both mesh wire and line wire. Confirm the value in the 2025 text for new contracts.

Under the 2003 edition, ± 3 mm for 25 mm mesh, ± 4 mm for 40 to 75 mm mesh and ± 5 mm for 100 to 150 mm mesh, measured as the clear distance between parallel wires.

No. The standard covers the fabric only. Posts, struts, base plates and fittings need their own specification in the tender.

Send us your chain link specification

Share the mesh size, wire diameter, coating, height and quantity, or your tender clause. Our team will confirm the construction against IS 2721 and send a quotation.