Indian Standard explained
IS 1566 explained:
reinforcement fabric
What the Indian Standard for hard drawn steel wire fabric requires, where it sits under the Quality Control Order, how its mass is calculated, and how it differs from IS 4948 weldmesh. Written by MM Industries, manufacturing welded mesh in Raipur since 1995.
Manufacturer since 1995 · ISO 9001:2015 certified plant
At a glance
| Current edition | IS 1566:1982 (Second Revision), with Amendments 1 to 4 |
|---|---|
| Official title | Specification for Hard-Drawn Steel Wire Fabric for Concrete Reinforcement |
| Last reviewed | May 2020, reaffirmed |
| Quality Control Order | Steel and Steel Products (Quality Control) Order, 2024. In force for IS 1566 since 26 February 2021 |
| Revision under way | Draft third revision, Cold Reduced Steel Wire Fabric for Concrete Reinforcement, circulated December 2024 |
| BIS committee | CED 54, Concrete Reinforcement |
Quick answer
IS 1566:1982 is the Bureau of Indian Standards specification for hard drawn steel wire fabric used as concrete reinforcement: hard drawn wire to IS 432 (Part 2) with cross wires electrically welded to it, in square or oblong mesh. It remains the current edition, with four amendments. It has been covered by a Quality Control Order since 26 February 2021. A third revision, retitled for cold reduced steel wire fabric, has been circulated in draft but not yet published.
Scope
What IS 1566 covers
IS 1566 covers welded fabric made for one job: reinforcing concrete. The main wires and cross wires are hard drawn steel wire, electrically welded at their intersections so the mesh holds its shape during handling and concreting. It is supplied as oblong mesh, where main and cross wires differ in pitch or size, or square mesh.
Because the fabric becomes part of a structural element, the standard ties every sheet back to the wire’s cast and to tests on the finished mesh, not just on the wire coil.
Latest status
Edition, amendments and the coming revision
| Date | Event |
|---|---|
| 1982 | Second revision of IS 1566 published |
| May 1984 | Amendment 1: elongation removed from the fabric property requirement; weld shear certification added |
| 1993 and 1994 | Amendments 2 and 3: weld shear test by mutual agreement, clause reference corrected |
| April 2007 | Amendment 4: square mesh sizes added at 25, 40 and 75 mm pitch |
| May 2020 | IS 1566:1982 reviewed and reaffirmed by CED 54 |
| 26 February 2021 | Quality Control Order implemented |
| December 2024 | Draft third revision circulated by CED 54, retitled Cold Reduced Steel Wire Fabric for Concrete Reinforcement |
| November 2026 | Third revision not yet published. IS 1566:1982 with four amendments remains current |
Until BIS publishes the third revision, IS 1566:1982 with its four amendments is the standard to cite. The draft moves the standard towards cold reduced wire, in line with the parallel draft revision of IS 432 (Part 2); watch for its publication before finalising long running contracts.
Requirements
Key requirements of the standard
Material and manufacture
- Wire to IS 432 (Part 2), hard drawn steel wire, suitable for welding. Every wire in the finished fabric must meet the minimum physical properties of IS 432 (Part 2).
- Main and cross wires electrically welded at intersections, within the specified displacement limits.
- Butt joints in the wire welded and staggered.
- Sheet width on a 10 cm module. Cross wires overhang each edge wire by half the main wire pitch unless otherwise specified.
Tolerances
| Parameter | Tolerance |
|---|---|
| Wire diameter | As IS 432 (Part 2) |
| Sheet dimension up to 5 m | ± 25 mm |
| Sheet dimension over 5 m | ± 1 percent |
| Mass, not specified as maximum or minimum | ± 6 percent |
| Mass, specified as a maximum | +0, −12 percent |
| Mass, specified as a minimum | +12, −0 percent |
Mesh pitch is also controlled, and the total number of meshes must not be less than the nominal pitch implies. Source: IS 1566:1982, clause 9.
Tests on the finished fabric
| Test | Requirement | Frequency |
|---|---|---|
| Tensile | On fabricated mesh, across one or more welds, to IS 1521 | One per 6,000 m² |
| Bend and rebend | To IS 1716, between welds, without annealing. Pin equal to the wire diameter up to 7.5 mm, twice the diameter above | One per 6,000 m² |
| Weld shear | On request, intersections withstand at least one quarter of the load from the specified proof stress of the smaller wire | As certified by the manufacturer |
Source: IS 1566:1982, clause 11 and Amendment 1.
Condition at delivery
- Free of oil, grease, paint, loose mill scale and loose rust. Limewash is permitted unless the purchaser specifies otherwise.
- No broken wires.
- Broken cross welds no more than 4 percent of all welded joints, and no more than half the joints on any one wire.
- Each bundle tagged and traceable to its cast.
Engineering
How fabric mass is calculated
IS 1566 calculates nominal mass from steel area: 0.785 kg per square centimetre of wire area per metre run, which is steel at 7,850 kg/m³.
For each direction, take the wire area per metre width, multiply by 0.785, and add the two directions together.
| Example | Main wires | Cross wires | Mass (kg/m²) |
|---|---|---|---|
| Square mesh 50 × 50 mm, 3.0 mm wire | 20 wires × 0.0707 cm² = 1.41 cm² → 1.11 kg | Same as main wires → 1.11 kg | 2.22 |
| Oblong mesh 75 × 250 mm, 5.0 × 4.2 mm wire | 13.3 wires × 0.196 cm² = 2.62 cm² → 2.06 kg | 4 wires × 0.139 cm² = 0.55 cm² → 0.43 kg | 2.49 |
Both results match the nominal masses listed in Appendix A of IS 1566, which tabulates the standard square and oblong fabrics.
Choosing the standard
IS 1566 or IS 4948?
| IS 1566 | IS 4948 | |
|---|---|---|
| Purpose | Concrete reinforcement | General use: fencing, grills, crates |
| Wire | Hard drawn wire to IS 432 (Part 2) | Mild steel wire to IS 280, or stainless steel |
| Tests | Tensile and bend on the finished fabric, weld shear on request | Weld shear on the fabric, wire tests before fabrication |
| Quality Control Order | Yes, since 2021 | No |
If the mesh will be cast into a structural slab, wall, pipe or precast element, the order is an IS 1566 order. IS 4948 states plainly that it does not cover concrete reinforcement. Read more in IS 4948 explained.
For buyers
How to specify IS 1566 fabric
- Cite IS 1566:1982, with the Appendix A reference number or a full description.
- For oblong fabric, state the main wire first: pitch and diameter of main wires, then cross wires.
- Sheet length and width, or roll dimensions, and the overhang required.
- Nominal mass per square metre, and whether it is a maximum or minimum.
- Test certificates for the tensile and bend tests on the finished fabric.
Manufacturer note
MM Industries manufactures MS welded mesh to IS 4948 for general use. Where your mesh is for structural concrete, tell us at enquiry so our team can confirm the right specification before we quote.
Questions
Frequently asked questions
Yes. Hard drawn steel wire fabric for concrete reinforcement under IS 1566 is covered by a Quality Control Order implemented on 26 February 2021.
Yes. It was last reaffirmed in May 2020. A draft third revision, retitled Cold Reduced Steel Wire Fabric for Concrete Reinforcement, was circulated in December 2024 but has not yet been published.
IS 1566 covers hard drawn wire fabric for concrete reinforcement and is covered by a Quality Control Order. IS 4948 covers welded fabric for general uses such as fencing and grills, and is not.
Multiply the wire area per metre width, in square centimetres, by 0.785 for each direction and add the two. Square 50 mm mesh in 3.0 mm wire works out to 2.22 kg/m².
No more than 4 percent of all welded joints, and no more than half the joints on any one wire.
A tensile test across welds and a bend and rebend test, each at one per 6,000 m² of fabric, with weld shear strength certified on request.
Keep reading
Related standards and tools
Tell us how the mesh will be used
Share the end use, wire diameters, pitch, sheet size and quantity, or your tender clause. Our team will confirm the correct standard before quoting.