MM Industries

Home › Resources › Standards › IS 1566

Indian Standard explained

IS 1566 explained:
reinforcement fabric

What the Indian Standard for hard drawn steel wire fabric requires, where it sits under the Quality Control Order, how its mass is calculated, and how it differs from IS 4948 weldmesh. Written by MM Industries, manufacturing welded mesh in Raipur since 1995.

Manufacturer since 1995 · ISO 9001:2015 certified plant

At a glance

Current editionIS 1566:1982 (Second Revision), with Amendments 1 to 4
Official titleSpecification for Hard-Drawn Steel Wire Fabric for Concrete Reinforcement
Last reviewedMay 2020, reaffirmed
Quality Control OrderSteel and Steel Products (Quality Control) Order, 2024. In force for IS 1566 since 26 February 2021
Revision under wayDraft third revision, Cold Reduced Steel Wire Fabric for Concrete Reinforcement, circulated December 2024
BIS committeeCED 54, Concrete Reinforcement

Quick answer

IS 1566:1982 is the Bureau of Indian Standards specification for hard drawn steel wire fabric used as concrete reinforcement: hard drawn wire to IS 432 (Part 2) with cross wires electrically welded to it, in square or oblong mesh. It remains the current edition, with four amendments. It has been covered by a Quality Control Order since 26 February 2021. A third revision, retitled for cold reduced steel wire fabric, has been circulated in draft but not yet published.

Scope

What IS 1566 covers

IS 1566 covers welded fabric made for one job: reinforcing concrete. The main wires and cross wires are hard drawn steel wire, electrically welded at their intersections so the mesh holds its shape during handling and concreting. It is supplied as oblong mesh, where main and cross wires differ in pitch or size, or square mesh.

Because the fabric becomes part of a structural element, the standard ties every sheet back to the wire’s cast and to tests on the finished mesh, not just on the wire coil.

Latest status

Edition, amendments and the coming revision

DateEvent
1982Second revision of IS 1566 published
May 1984Amendment 1: elongation removed from the fabric property requirement; weld shear certification added
1993 and 1994Amendments 2 and 3: weld shear test by mutual agreement, clause reference corrected
April 2007Amendment 4: square mesh sizes added at 25, 40 and 75 mm pitch
May 2020IS 1566:1982 reviewed and reaffirmed by CED 54
26 February 2021Quality Control Order implemented
December 2024Draft third revision circulated by CED 54, retitled Cold Reduced Steel Wire Fabric for Concrete Reinforcement
November 2026Third revision not yet published. IS 1566:1982 with four amendments remains current

Until BIS publishes the third revision, IS 1566:1982 with its four amendments is the standard to cite. The draft moves the standard towards cold reduced wire, in line with the parallel draft revision of IS 432 (Part 2); watch for its publication before finalising long running contracts.

Requirements

Key requirements of the standard

Material and manufacture

  • Wire to IS 432 (Part 2), hard drawn steel wire, suitable for welding. Every wire in the finished fabric must meet the minimum physical properties of IS 432 (Part 2).
  • Main and cross wires electrically welded at intersections, within the specified displacement limits.
  • Butt joints in the wire welded and staggered.
  • Sheet width on a 10 cm module. Cross wires overhang each edge wire by half the main wire pitch unless otherwise specified.

Tolerances

ParameterTolerance
Wire diameterAs IS 432 (Part 2)
Sheet dimension up to 5 m± 25 mm
Sheet dimension over 5 m± 1 percent
Mass, not specified as maximum or minimum± 6 percent
Mass, specified as a maximum+0, −12 percent
Mass, specified as a minimum+12, −0 percent

Mesh pitch is also controlled, and the total number of meshes must not be less than the nominal pitch implies. Source: IS 1566:1982, clause 9.

Tests on the finished fabric

TestRequirementFrequency
TensileOn fabricated mesh, across one or more welds, to IS 1521One per 6,000 m²
Bend and rebendTo IS 1716, between welds, without annealing. Pin equal to the wire diameter up to 7.5 mm, twice the diameter aboveOne per 6,000 m²
Weld shearOn request, intersections withstand at least one quarter of the load from the specified proof stress of the smaller wireAs certified by the manufacturer

Source: IS 1566:1982, clause 11 and Amendment 1.

Condition at delivery

  • Free of oil, grease, paint, loose mill scale and loose rust. Limewash is permitted unless the purchaser specifies otherwise.
  • No broken wires.
  • Broken cross welds no more than 4 percent of all welded joints, and no more than half the joints on any one wire.
  • Each bundle tagged and traceable to its cast.

Engineering

How fabric mass is calculated

IS 1566 calculates nominal mass from steel area: 0.785 kg per square centimetre of wire area per metre run, which is steel at 7,850 kg/m³.

For each direction, take the wire area per metre width, multiply by 0.785, and add the two directions together.

ExampleMain wiresCross wiresMass (kg/m²)
Square mesh 50 × 50 mm, 3.0 mm wire20 wires × 0.0707 cm² = 1.41 cm² → 1.11 kgSame as main wires → 1.11 kg2.22
Oblong mesh 75 × 250 mm, 5.0 × 4.2 mm wire13.3 wires × 0.196 cm² = 2.62 cm² → 2.06 kg4 wires × 0.139 cm² = 0.55 cm² → 0.43 kg2.49

Both results match the nominal masses listed in Appendix A of IS 1566, which tabulates the standard square and oblong fabrics.

Choosing the standard

IS 1566 or IS 4948?

IS 1566IS 4948
PurposeConcrete reinforcementGeneral use: fencing, grills, crates
WireHard drawn wire to IS 432 (Part 2)Mild steel wire to IS 280, or stainless steel
TestsTensile and bend on the finished fabric, weld shear on requestWeld shear on the fabric, wire tests before fabrication
Quality Control OrderYes, since 2021No

If the mesh will be cast into a structural slab, wall, pipe or precast element, the order is an IS 1566 order. IS 4948 states plainly that it does not cover concrete reinforcement. Read more in IS 4948 explained.

For buyers

How to specify IS 1566 fabric

  • Cite IS 1566:1982, with the Appendix A reference number or a full description.
  • For oblong fabric, state the main wire first: pitch and diameter of main wires, then cross wires.
  • Sheet length and width, or roll dimensions, and the overhang required.
  • Nominal mass per square metre, and whether it is a maximum or minimum.
  • Test certificates for the tensile and bend tests on the finished fabric.

Manufacturer note

MM Industries manufactures MS welded mesh to IS 4948 for general use. Where your mesh is for structural concrete, tell us at enquiry so our team can confirm the right specification before we quote.

Questions

Frequently asked questions

Yes. Hard drawn steel wire fabric for concrete reinforcement under IS 1566 is covered by a Quality Control Order implemented on 26 February 2021.

Yes. It was last reaffirmed in May 2020. A draft third revision, retitled Cold Reduced Steel Wire Fabric for Concrete Reinforcement, was circulated in December 2024 but has not yet been published.

IS 1566 covers hard drawn wire fabric for concrete reinforcement and is covered by a Quality Control Order. IS 4948 covers welded fabric for general uses such as fencing and grills, and is not.

Multiply the wire area per metre width, in square centimetres, by 0.785 for each direction and add the two. Square 50 mm mesh in 3.0 mm wire works out to 2.22 kg/m².

No more than 4 percent of all welded joints, and no more than half the joints on any one wire.

A tensile test across welds and a bend and rebend test, each at one per 6,000 m² of fabric, with weld shear strength certified on request.

Tell us how the mesh will be used

Share the end use, wire diameters, pitch, sheet size and quantity, or your tender clause. Our team will confirm the correct standard before quoting.