Indian Standard explained
IS 2721 explained:
chain link fence fabric
What the Indian Standard for chain link fence fabric requires, what changed in the 2025 revision, and how to write it into a purchase order or tender. Written by MM Industries, manufacturing chain link fence at our own plant in Raipur since 1995.
Manufacturer since 1995 · ISO 9001:2015 certified plant
At a glance
| Current edition | IS 2721:2025 (Third Revision) |
|---|---|
| Official title | Galvanized Polyvinyl Chloride (PVC), Polyolefin and Other Polymer Coated Steel Chain Link Fence Fabric — Specification |
| Established | 10 December 2025 |
| Replaces | IS 2721:2003, in force alongside it until 10 June 2027 |
| BIS committee | MED 10, Wire Ropes and Wire Products |
| Certification | Voluntary. BIS lists no Quality Control Order for this product at the time of writing |
Quick answer
IS 2721 is the Bureau of Indian Standards specification for steel chain link fence fabric. The current edition is IS 2721:2025, the third revision, established on 10 December 2025. IS 2721:2003 stays in force alongside it until 10 June 2027, after BIS extended its withdrawal by one year, but new tenders and purchase orders should cite IS 2721:2025. The standard governs the wire, its coating, mesh size and tolerance, selvage, roll dimensions and the tests the wire must pass before fabric is accepted.
On this page
Scope
What IS 2721 covers
IS 2721 defines chain link fence fabric as steel wire that is helically wound and interwoven into a continuous diamond mesh, with no knots or ties anywhere except at the selvage, where the wire ends are knuckled or twisted. That construction is what separates chain link from welded mesh: every wire is free to articulate, so the fabric follows the ground and spreads an impact load across many links.
The standard covers the fabric only. Line posts, straining posts, struts, base plates and fittings sit outside it, so a complete fence specification has to name those separately. In our experience this is the most common gap in tender documents: the fabric is specified to IS 2721 and the framework is left undefined.
Manufacturer note
The 2025 title now names PVC, polyolefin and other polymer coated chain link fabric alongside galvanized fabric. Coated chain link, sold widely as PVC chain link, is therefore within the scope of the current standard, and a coated order should state the coating type and colour in the same way a galvanized order states the zinc coating.
Latest status
What changed, and when
IS 2721 has been revised three times since it was first issued. The dates below decide which edition a contract can cite.
| Date | Event |
|---|---|
| 1964 | First edition of IS 2721 published by BIS |
| 2003 | Second revision. Selvage types introduced, fabric length and width set to the purchaser’s requirement, zinc coating raised to heavy coating, packing clause amended |
| March 2024 | IS 2721:2003 reviewed by the MED 10 committee |
| 10 December 2025 | IS 2721:2025, the third revision, established |
| 27 October 2026 | BIS corrigendum moves the withdrawal of IS 2721:2003 from 10 June 2026 to 10 June 2027 |
| 10 June 2027 | IS 2721:2003 withdrawn. IS 2721:2025 becomes the only valid edition |
Both editions are in force together until 10 June 2027. BIS first set the withdrawal of the 2003 edition for 10 June 2026, then extended it by one year through a corrigendum dated 27 October 2026. A contract can still cite IS 2721:2003 until then, but supply after June 2027 must meet IS 2721:2025, so update tender templates and approved vendor documents now.
How to read the figures below
Where this page quotes clause values, such as tolerances, test limits and sampling, they are taken from the 2003 edition, which remains in force until 10 June 2027. Confirm each value against the IS 2721:2025 text before writing it into a contract. Our team will check any clause for you at enquiry.
Requirements
Key requirements of the standard
Wire and coating
- Mesh wire and line wire are galvanized mild steel wire to IS 280, with a tensile strength of 400 to 550 MPa.
- The zinc coating is the heavy grade of IS 4826 (hot dip) or IS 12753 (electrogalvanized). Line wire must meet the heavy coating requirement in full.
- Mesh wire tested after weaving may fall up to 10 percent below the specified minimum zinc mass, an allowance for the coating disturbed during weaving.
- Wire must be circular and free from scale, splits and other defects, and the zinc coating must be smooth, even and bright.
Mesh size and tolerance
| Nominal mesh size | Tolerance |
|---|---|
| 25 mm | ± 3 mm |
| 40, 50, 63 and 75 mm | ± 4 mm |
| 100, 125 and 150 mm | ± 5 mm |
Mesh size is the minimum clear distance between parallel wires with the fabric in its normal stretched condition. Sizes outside this range are by agreement between purchaser and manufacturer. Source: IS 2721:2003, Table 1.
Selvage types
| Type | Top and bottom edges | Typical use |
|---|---|---|
| Both ends twisted | Wire ends twisted together in a close helix at both edges | Higher security, where a sharp top edge is a deterrent |
| One end knuckled, one end twisted | Rounded loop at one edge, twisted points at the other | Knuckled edge at ground level, twisted edge at the top |
| Both ends knuckled | Adjacent wire ends interlocked and bent back into a loop at both edges | Schools, sports grounds and public areas |
| Both ends neither knuckled nor twisted | Plain cut ends at both edges | Fabric to be cut or joined on site |
Dimensions and workmanship
- Standard widths of 0.90, 1.20, 1.50, 1.80, 2.00, 2.50 and 3.00 m, or as the purchaser requires.
- Roll lengths of 5, 10, 15, 20 or 25 m, or as the purchaser requires. Measured fully stretched, a roll must not be shorter than its stated length.
- Two line wires for fabric up to 2 m high, at top and bottom. Three line wires, at top, middle and bottom, for fabric 2.5 m high and above.
- No welds or splices within a roll. Rust on cut selvage ends is inherent and is not a ground for rejection.
Acceptance
Tests and acceptance
The mechanical tests are carried out on the coil wire before it is woven, which is why a mill test certificate for the wire is part of every serious chain link supply.
| Test | Requirement | Method |
|---|---|---|
| Tensile | 400 to 550 MPa for mesh and line wire | IS 1608 |
| Wrapping | No break or split after eight turns around its own diameter, then straightened | IS 1755 |
| Torsion | At least 18 twists over a length of 100 wire diameters | IS 1717 |
| Bend (wire of 5 mm and above) | Bent through 90 degrees around a former of twice the wire diameter without breaking or splitting | IS 2721 |
| Zinc coating | Heavy coating mass and uniformity | IS 4826 or IS 12753 |
Source: IS 2721:2003, clause 9.
Sampling
| Rolls in the lot | Rolls tested (physical and dimensional) | Rolls tested (zinc coating) |
|---|---|---|
| Up to 25 | 2 | 1 |
| 26 to 50 | 3 | 1 |
| 51 to 150 | 5 | 2 |
| 151 to 300 | 8 (1 defective allowed) | 2 |
| 301 and above | 13 (1 defective allowed) | 2 |
A lot is all rolls with the same mesh size, wire diameter, width and roll length made under similar conditions. No defective is allowed in the zinc coating sample. Source: IS 2721:2003, Annex A.
Marking on every roll
- Manufacturer’s name or trademark
- Lot number and roll number
- Mesh size and the diameters of line wire and mesh wire
- Length and width of the fabric
- The BIS Standard Mark, only where the manufacturer holds a BIS licence for the product
For buyers
How to specify IS 2721 in a purchase order
A tight chain link specification leaves nothing to interpretation at the site gate. This is the checklist our team works through with every buyer.
- Cite the standard with its year: IS 2721:2025.
- Mesh size in millimetres, for example 50 mm, and accept the standard tolerance.
- Mesh wire diameter in millimetres. SWG alone is ambiguous across suppliers.
- Coating: heavy zinc coating, or the polymer type and colour for coated fabric.
- Selvage type for the top and bottom edges.
- Fabric height, roll length and the number of line wires.
- Documents: wire mill test certificate, lot test report and roll marking as per the standard.
From the plant floor
Weight is the quickest check on a delivered roll. Underweight fabric almost always means thinner wire than ordered. Use our chain link weight calculator to set the theoretical weight per roll before you raise the order, then weigh rolls at receipt.
Our practice
How we manufacture chain link fence
MM Industries manufactures GI and PVC coated chain link fence to IS 2721 at our plant on NH 43, Raipur, which has run since 1995. Our standard range is 2.0 to 4.0 mm wire (14 to 8 SWG) in 25 to 100 mm mesh, in roll heights from 3 to 10 ft. Our quality management system is certified to ISO 9001:2015, and the wire mill test certificate is supplied with every lot.
One practical point for buyers: our 25 mm mesh is made in 14 SWG wire only. If your tender calls for 25 mm mesh in a heavier gauge, speak to our team before the document is issued.
Questions
Frequently asked questions
Yes, until 10 June 2027. BIS established IS 2721:2025 on 10 December 2025 and, by a corrigendum dated 27 October 2026, moved the withdrawal of IS 2721:2003 from 10 June 2026 to 10 June 2027. New tenders and purchase orders should still cite IS 2721:2025.
BIS lists no Quality Control Order for chain link fence fabric at the time of writing, so certification is voluntary.
Yes. The 2025 revision names PVC, polyolefin and other polymer coated chain link fabric in its title, alongside galvanized fabric.
The 2003 edition required 400 to 550 MPa for both mesh wire and line wire. Confirm the value in the 2025 text for new contracts.
Under the 2003 edition, ± 3 mm for 25 mm mesh, ± 4 mm for 40 to 75 mm mesh and ± 5 mm for 100 to 150 mm mesh, measured as the clear distance between parallel wires.
No. The standard covers the fabric only. Posts, struts, base plates and fittings need their own specification in the tender.
Keep reading
Related standards and tools
Product
Chain link fence
Our GI and PVC coated chain link range, sizes and applications.
Open →
Calculator
Chain link weight calculator
Theoretical weight per square metre and per roll for any wire and mesh.
Open →
Standard
IS 278: barbed wire
The standard for the barbed wire strands that top most chain link fences.
Open →
Send us your chain link specification
Share the mesh size, wire diameter, coating, height and quantity, or your tender clause. Our team will confirm the construction against IS 2721 and send a quotation.